Difference between revisions of "Slant Six"
| Line 2: | Line 2: | ||
[[Category:Engines]] | [[Category:Engines]] | ||
{{Template:Openx}} | {{Template:Openx}} | ||
| − | |||
| − | The Slant six was a [[Mopar]] six cylinder motor | + | == Origins == |
| + | |||
| + | The Slant six was a [[Mopar]] first ever [[ohv]] six cylinder motor, which began production in 1960. While most other American six cylinder engines had the block orientated with the cylinders north and south at a 90 degree arrangement, the Slant Six (aka the "Leaning Tower of Power") leaned the cylinders over 30 degrees on a slant to allow for the lower hoods in the new [[compact]] [[A-Body]] [[models]], the [[Valiant]] (not originally a [[Plymouth]] when released in 1960, but it's own make) and the later (introduced in 1961) [[Dodge]] [[Lancer]]. It also replaced the aging [[Flathead Six]] used in the entry level Plymouths and Dodge's junior model [[Darts]] (still full size) retired after 1959. | ||
| + | |||
| + | Originally referred to as the "G" Engine, it came in two iterations - the low block "LG" and the raised block "RG". Both had a [[cylinder bore]] of 3.40", but the "LG" had a [[stroke]] of 3.125", while the "RG" had a 4.125" stroke. The [[CID]] of the "LG" was 170 and it developed 101 [[bhp]] at 4400 [[rpm]], and the 1" taller (overall height) "RG" was 225 CID developing 140 bhp at 4000 rpm. Both engines were 8.2:1 [[compression]]. | ||
| + | |||
| + | In addition to offering a lower hood height, the Slant Six was able to have a long branch [[intake manifold]] for greater breathing capacity and better fuel economy, and it allowed for the [[water pump]] to be offset to the side (instead of in front) for a shorter engine. | ||
| + | |||
| + | While the standard manual transmission was a 3-speed, a special [[A-904]] [[TorqueFlite]] automatic [[transmission]] with a 1-piece aluminum case and lighter internal components was developed for the Slant Six used in the Valiants and Lancers. They weighed about 100 less than the [[A-727]] transmission. | ||
| + | |||
| + | == Production == | ||
| + | |||
| + | All Slant Six engines were made in the [[Trenton, MI Plant]]. They were used in passenger cars from 1960-1983, light trucks from 1961-1987, and on trucks made in Mexico through 1991. A total of 8,152,768 Slant Six engines were built in the Trento Plant from 1960-1983. | ||
| + | |||
| + | == Aluminum Block == | ||
| + | |||
| + | == Hyper Pack == | ||
| + | |||
| + | == References == | ||
| + | |||
{{Template:BottomWiki}} | {{Template:BottomWiki}} | ||
Revision as of 21:55, 15 September 2013
Origins
The Slant six was a Mopar first ever ohv six cylinder motor, which began production in 1960. While most other American six cylinder engines had the block orientated with the cylinders north and south at a 90 degree arrangement, the Slant Six (aka the "Leaning Tower of Power") leaned the cylinders over 30 degrees on a slant to allow for the lower hoods in the new compact A-Body models, the Valiant (not originally a Plymouth when released in 1960, but it's own make) and the later (introduced in 1961) Dodge Lancer. It also replaced the aging Flathead Six used in the entry level Plymouths and Dodge's junior model Darts (still full size) retired after 1959.
Originally referred to as the "G" Engine, it came in two iterations - the low block "LG" and the raised block "RG". Both had a cylinder bore of 3.40", but the "LG" had a stroke of 3.125", while the "RG" had a 4.125" stroke. The CID of the "LG" was 170 and it developed 101 bhp at 4400 rpm, and the 1" taller (overall height) "RG" was 225 CID developing 140 bhp at 4000 rpm. Both engines were 8.2:1 compression.
In addition to offering a lower hood height, the Slant Six was able to have a long branch intake manifold for greater breathing capacity and better fuel economy, and it allowed for the water pump to be offset to the side (instead of in front) for a shorter engine.
While the standard manual transmission was a 3-speed, a special A-904 TorqueFlite automatic transmission with a 1-piece aluminum case and lighter internal components was developed for the Slant Six used in the Valiants and Lancers. They weighed about 100 less than the A-727 transmission.
Production
All Slant Six engines were made in the Trenton, MI Plant. They were used in passenger cars from 1960-1983, light trucks from 1961-1987, and on trucks made in Mexico through 1991. A total of 8,152,768 Slant Six engines were built in the Trento Plant from 1960-1983.
Aluminum Block
Hyper Pack
References
Random Page | Longest Wikis | Oldest Wikis | Newest Images | Newest Wikis | List of Categories | List of Every Freakin Wiki
- Register to Edit
- It takes less than 5 minutes to request registration for editing, and we try to approve within 24 hours. Click the Register Link in the Top Bar.
- MoparWiki Help
- While editing Wikis may at first glance appear a little overwhelming, it really isn't. You will find this site's HELP (link found in the sidebar) to be very strong and easy to understand. The best way to start is with small edits and working on your user page -- and you will become a Pro in no time.
