Difference between revisions of "Clutch"

From MoparWiki
Jump to: navigation, search
(Created page with " <!-- Start of Comments this information is to help the person collaborating on the Wiki Page Terminology Template Copy all of the information on this page and paste it ont...")
 
 
(One intermediate revision by the same user not shown)
Line 1: Line 1:
<!-- Start of Comments this information is to help the person collaborating on the Wiki Page
+
[[Category:Parts]] <!-- delete this line -->
Terminology Template
 
Copy all of the information on this page and paste it onto a new page for a particular Mopar car model
 
The standard for images are as Thumbnails of 300 pixels wide with a description, ie: [Image:FilenameUploaded|Thumb|300px|Short Photo Description]]
 
Change the Category below the Comments to the appropriate category(s). In the special pages you will find a link to the list of categories.
 
Enclosed the first instance of a Mopar key word in a double set of brackets so that it will link to its MoparWiki page
 
Example: [[Richard Petty]] raced a [[Plymouth]] [[Superbird]] during his 1970 season in [[NASCAR]].
 
End of comments - Delete nothing this line and above -->
 
 
 
[[Category:Page Templates]] <!-- delete this line -->
 
 
[[Category:Terminology]] <!-- Leave this line -->
 
[[Category:Terminology]] <!-- Leave this line -->
  
{{Template:Openx}} <!-- Do not remove this line -->
+
{{Template:TopWiki}} <!-- Do not remove this line -->
  
 
The vast majority of clutches ultimately rely on frictional forces for their operation. The purpose of friction clutches is to connect a moving member to another that is moving at a different speed or stationary, often to synchronise the speeds, and/or to transmit power. Usually as little slippage (difference in speeds) as possible between the two members is desired.
 
The vast majority of clutches ultimately rely on frictional forces for their operation. The purpose of friction clutches is to connect a moving member to another that is moving at a different speed or stationary, often to synchronise the speeds, and/or to transmit power. Usually as little slippage (difference in speeds) as possible between the two members is desired.
Line 28: Line 19:
  
 
== [[References]] ==
 
== [[References]] ==
 +
 +
*[http://en.wikipedia.org/wiki/Clutch Wikipedia]

Latest revision as of 04:44, 27 April 2020





Discussion.png
If you have information, corrections or reference links that could improve this Wiki, but are uncomfortable with editing in the markup language - you can click the Discussion Tab above and freehand type your information. An editor usually checks the discussion prior to editing the Wiki.


The vast majority of clutches ultimately rely on frictional forces for their operation. The purpose of friction clutches is to connect a moving member to another that is moving at a different speed or stationary, often to synchronise the speeds, and/or to transmit power. Usually as little slippage (difference in speeds) as possible between the two members is desired.

There are different designs of vehicle clutch but most are based on one or more friction discs pressed tightly together or against a flywheel using springs. The friction material varies in composition depending on many considerations such as whether the clutch is "dry" or "wet". Friction discs once contained asbestos but this has been largely eliminated. Clutches found in heavy duty applications such as trucks and competition cars use ceramic clutches that have a greatly increased friction coefficient. However, these have a "grabby" action generally considered unsuitable for passenger cars. The spring pressure is released when the clutch pedal is depressed thus either pushing or pulling the diaphragm of the pressure plate, depending on type. However, raising the engine speed too high while engaging the clutch causes excessive clutch plate wear. Engaging the clutch abruptly when the engine is turning at high speed causes a harsh, jerky start. This kind of start is necessary and desirable in drag racing and other competitions, where speed is more important than comfort.

In a modern car with a manual transmission the clutch is operated by the left-most pedal using a hydraulic or cable connection from the pedal to the clutch mechanism. On older cars the clutch might be operated by a mechanical linkage. Even though the clutch may physically be located very close to the pedal, such remote means of actuation are necessary to eliminate the effect of vibrations and slight engine movement, engine mountings being flexible by design. With a rigid mechanical linkage, smooth engagement would be near-impossible because engine movement inevitably occurs as the drive is "taken up."

The default state of the clutch is engaged - that is the connection between engine and gearbox is always "on" unless the driver presses the pedal and disengages it. If the engine is running with clutch engaged and the transmission in neutral, the engine spins the input shaft of the transmission, but no power is transmitted to the wheels.

The clutch is located between the engine and the gearbox, as disengaging it is required to change gear. Although the gearbox does not stop rotating during a gear change, there is no torque transmitted through it, thus less friction between gears and their engagement dogs. The output shaft of the gearbox is permanently connected to the final drive, then the wheels, and so both always rotate together, at a fixed speed ratio. With the clutch disengaged, the gearbox input shaft is free to change its speed as the internal ratio is changed. Any resulting difference in speed between the engine and gearbox is evened out as the clutch slips slightly during re-engagement.

Clutches in typical cars are mounted directly to the face of the engine's flywheel, as this already provides a convenient large diameter steel disk that can act as one driving plate of the clutch. Some racing clutches use small multi-plate disk packs that are not part of the flywheel. Both clutch and flywheel are enclosed in a conical bellhousing, which (in a rear-wheel drive car) usually forms the main mounting for the gearbox.


Random Page | Longest Wikis | Oldest Wikis | Newest Images | Newest Wikis | List of Categories | List of Every Freakin Wiki



Register to Edit
It takes less than 5 minutes to request registration for editing, and we try to approve within 24 hours. Click the Register Link in the Top Bar.
MoparWiki Help
While editing Wikis may at first glance appear a little overwhelming, it really isn't. You will find this site's HELP (link found in the sidebar) to be very strong and easy to understand. The best way to start is with small edits and working on your user page -- and you will become a Pro in no time.

References