Difference between revisions of "Automatic transmission"

From MoparWiki
Jump to: navigation, search
Line 51: Line 51:
 
General Motors produced multiple-turbine torque converters from 1954 to 1961. These included the Twin-Turbine Dynaflow and the triple-turbine Turboglide transmissions. The shifting took place in the torque converter, rather than through pressure valves and changes in planetary gear connections. Each turbine was connected to the drive shaft through a different gear train. These phased from one ratio to another according to demand, rather than shifting. The Turboglide actually had two speed ratios in reverse, with one of the turbines rotating backwards.
 
General Motors produced multiple-turbine torque converters from 1954 to 1961. These included the Twin-Turbine Dynaflow and the triple-turbine Turboglide transmissions. The shifting took place in the torque converter, rather than through pressure valves and changes in planetary gear connections. Each turbine was connected to the drive shaft through a different gear train. These phased from one ratio to another according to demand, rather than shifting. The Turboglide actually had two speed ratios in reverse, with one of the turbines rotating backwards.
  
By the late 1960s, most of the fluid-coupling four-speed and two-speed transmissions had disappeared in favor of three-speed units with torque converters. Also around this time, whale oil was removed from automatic transmission fluid.[4] By the early 1980s, these were being supplemented and eventually replaced by overdrive-equipped transmissions providing four or more forward speeds. Many transmissions also adopted the lock-up torque converter (a mechanical clutch locking the torque converter pump and turbine together to eliminate slip at cruising speed) to improve fuel economy.
+
By the late 1960s, most of the fluid-coupling four-speed and two-speed transmissions had disappeared in favor of three-speed units with torque converters. Also around this time, whale oil was removed from automatic transmission fluid. By the early 1980s, these were being supplemented and eventually replaced by overdrive-equipped transmissions providing four or more forward speeds. Many transmissions also adopted the lock-up torque converter (a mechanical clutch locking the torque converter pump and turbine together to eliminate slip at cruising speed) to improve fuel economy.
  
 
As computerized engine control units (ECUs) became more capable, much of the logic built into the transmission's valve body was offloaded to the ECU. Some manufacturers use a separate computer dedicated to the transmission called a transmission control unit (TCU), also known as the transmission control module (TCM), which shares information with the engine management computer. In this case, solenoids turned on and off by the computer control shift patterns and gear ratios, rather than the spring-loaded valves in the valve body. This allows for more precise control of shift points, shift quality, lower shift times, and (on some newer cars) semi-automatic control, where the driver tells the computer when to shift. The result is an impressive combination of efficiency and smoothness. Some computers even identify the driver's style and adapt to best suit it.
 
As computerized engine control units (ECUs) became more capable, much of the logic built into the transmission's valve body was offloaded to the ECU. Some manufacturers use a separate computer dedicated to the transmission called a transmission control unit (TCU), also known as the transmission control module (TCM), which shares information with the engine management computer. In this case, solenoids turned on and off by the computer control shift patterns and gear ratios, rather than the spring-loaded valves in the valve body. This allows for more precise control of shift points, shift quality, lower shift times, and (on some newer cars) semi-automatic control, where the driver tells the computer when to shift. The result is an impressive combination of efficiency and smoothness. Some computers even identify the driver's style and adapt to best suit it.
  
ZF Friedrichshafen and BMW were responsible for introducing the first six-speed (the ZF 6HP26 in the 2002 BMW E65 7-Series). Mercedes-Benz's 7G-Tronic was the first seven-speed in 2003, with Toyota introducing an eight-speed in 2007 on the Lexus LS 460. Derived from the 7G-Tronic, Mercedes-Benz unveiled a semi-automatic transmission with the torque converter replaced with a wet multi clutch called the AMG SPEEDSHIFT MCT.[5] The 2014 Jeep Cherokee has the world's first nine-speed automatic transmission for a passenger vehicle to market.
+
ZF Friedrichshafen and BMW were responsible for introducing the first six-speed (the ZF 6HP26 in the 2002 BMW E65 7-Series). Mercedes-Benz's 7G-Tronic was the first seven-speed in 2003, with Toyota introducing an eight-speed in 2007 on the Lexus LS 460. Derived from the 7G-Tronic, Mercedes-Benz unveiled a semi-automatic transmission with the torque converter replaced with a wet multi clutch called the AMG SPEEDSHIFT MCT. The 2014 Jeep Cherokee has the world's first nine-speed automatic transmission for a passenger vehicle to market.
  
 
===Hydraulic automatic transmissions===
 
===Hydraulic automatic transmissions===

Revision as of 23:12, 23 September 2017




An automatic transmission, also called auto, self-shifting transmission, n-speed automatic (where n is its number of forward gear ratios), or AT, is a type of motor vehicle transmission that can automatically change gear ratios as the vehicle moves, freeing the driver from having to shift gears manually. Like other transmission systems on vehicles, it allows an internal combustion engine, best suited to run at a relatively high rotational speed, to provide a range of speed and torque outputs necessary for vehicular travel. The number of forward gear ratios is often expressed for manual transmissions as well (e.g., 6-speed manual).

The most popular form found in automobiles is the hydraulic automatic transmission. Similar but larger devices are also used for heavy-duty commercial and industrial vehicles and equipment. This system uses a fluid coupling in place of a friction clutch, and accomplishes gear changes by hydraulically locking and unlocking a system of planetary gears. These systems have a defined set of gear ranges, often with a parking pawl that locks the output shaft of the transmission to keep the vehicle from rolling either forward or backward. Some machines with limited speed ranges or fixed engine speeds, such as some forklifts and lawn mowers, only use a torque converter to provide a variable gearing of the engine to the wheels.

Besides the traditional hydraulic automatic transmissions, there are also other types of automated transmissions, such as a continuously variable transmission (CVT) and semi-automatic transmissions, that free the driver from having to shift gears manually, by using the transmission's computer to change gear, if for example the driver were redlining the engine. Despite superficial similarity to other transmissions, traditional automatic transmissions differ significantly in internal operation and driver's feel from semi-automatics and CVTs. In contrast to conventional automatic transmissions, a CVT uses a belt or other torque transmission scheme to allow an "infinite" number of gear ratios instead of a fixed number of gear ratios. A semi-automatic retains a clutch like a manual transmission, but controls the clutch through electrohydraulic means. The ability to shift gears manually, often via paddle shifters, can also be found on certain automated transmissions (manumatics such as Tiptronic), semi-automatics (BMW SMG, VW Group DSG), and CVTs (such as Lineartronic).

The obvious advantage of an automatic transmission to the driver is the lack of a clutch pedal and manual shift pattern in normal driving. This allows the driver to operate the car with as few as two limbs (possibly using assist devices to position controls within reach of usable limbs), allowing amputees and other disabled individuals to drive. The lack of manual shifting also reduces the attention and workload required inside the cabin, such as monitoring the tachometer and taking a hand off the wheel to move the shifter, allowing the driver to ideally keep both hands on the wheel at all times and to focus more on the road. Control of the car at low speeds is often easier with an automatic than a manual, due to a side effect of the clutchless fluid-coupling design called "creep" that causes the car to want to move while in a driving gear, even at idle. The primary disadvantage of the most popular hydraulic designs is reduced mechanical efficiency of the power transfer between engine and drivetrain, due to the fluid coupling connecting the engine to the gearbox. This can result in lower power/torque ratings for automatics compared to manuals with the same engine specs, as well as reduced fuel efficiency in city driving as the engine must maintain idle against the resistance of the fluid coupling. Advances in transmission and coupler design have narrowed this gap considerably, but clutch-based transmissions (manual or semi-automatic) are still preferred in sport-tuned trim levels of various production cars, as well as in many auto racing leagues.

The automatic transmission was invented in 1921 by Alfred Horner Munro of Regina, Saskatchewan, Canada, and patented under Canadian patent CA 235757 in 1923. (Munro obtained UK patent GB215669 215,669 for his invention in 1924 and US patent 1,613,525 on 4 January 1927). Being a steam engineer, Munro designed his device to use compressed air rather than hydraulic fluid, and so it lacked power and never found commercial application. The first automatic transmission using hydraulic fluid may have been developed in 1932 by two Brazilian engineers, José Braz Araripe and Fernando Lehly Lemos; subsequently the prototype and plans were sold to General Motors who introduced it in the 1940 Oldsmobile as the "Hydra-Matic" transmission. They were incorporated into GM-built tanks during World War II and, after the war, GM marketed them as being "battle-tested."[citation needed] However, a Wall Street Journal article credits ZF Friedrichshafen with the invention, occurring shortly after World War I. ZF's origins were in manufacturing gears for airship engines beginning in 1915; the company was founded by Ferdinand von Zeppelin.

History

Modern automatic transmissions can trace their origins to an early "horseless carriage" gearbox that was developed in 1904 by the Sturtevant brothers of Boston, Massachusetts. This unit had two forward speeds, the ratio change being brought about by flyweights that were driven by the engine. At higher engine speeds, high gear was engaged. As the vehicle slowed down and engine RPM decreased, the gearbox would shift back to low. Unfortunately, the metallurgy of the time wasn't up to the task, and owing to the abruptness of the gear change, the transmission would often fail without warning.

The next significant phase in the automatic transmission's development occurred in 1908 with the introduction of Henry Ford's remarkable Model T. The Model T, in addition to being cheap and reliable by the standards of the day, featured a simple, two speed plus reverse planetary transmission whose operation was manually controlled by the driver using pedals. The pedals actuated the transmission's friction elements (bands and clutches) to select the desired gear. In some respects, this type of transmission was less demanding of the driver's skills than the contemporary, unsynchronized manual transmission, but still required that the driver know when to make a shift, as well as how to get the car off to a smooth start.

The first automatic transmission using hydraulic fluid was developed in 1932 by two Brazilian engineers, José Braz Araripe and Fernando Lehly Lemos;[citation needed] Later, the prototype and the project were sold to General Motors, who introduced the technology in the 1940 Oldsmobile model as a "Hydra-Matic" transmission. However, an article published by the Wall Street Journal credits the German auto parts company ZF Friedrichshafen for the invention, which would have occurred shortly after World War I.

In 1934, both REO and General Motors developed semi-automatic transmissions that were less difficult to operate than a fully manual unit. These designs, however, continued to use a clutch to engage the engine with the transmission. The General Motors unit, dubbed the "Automatic Safety Transmission," was notable in that it employed a power-shifting planetary gearbox that was hydraulically controlled and was sensitive to road speed, anticipating future development.

Parallel to the development in the 1930s of an automatically shifting gearbox was Chrysler's work on adapting the fluid coupling to automotive use. Invented early in the 20th century, the fluid coupling was the answer to the question of how to avoid stalling the engine when the vehicle was stopped with the transmission in gear. Chrysler itself never used the fluid coupling with any of its automatic transmissions, but did use it in conjunction with a hybrid manual transmission called "Fluid Drive" (the similar Hy-Drive used a torque converter). These developments in automatic gearbox and fluid coupling technology eventually culminated in the introduction in 1939 of the General Motors Hydra-Matic, the world's first mass-produced automatic transmission.

Available as an option on 1940 Oldsmobiles and later Cadillacs, the Hydra-Matic combined a fluid coupling with three hydraulically controlled planetary gearsets to produce four forward speeds plus reverse. The transmission was sensitive to engine throttle position and road speed, producing fully automatic up- and down-shifting that varied according to operating conditions.

The Hydra-Matic was subsequently adopted by Cadillac and Pontiac, and was sold to various other automakers, including Bentley, Hudson, Kaiser, Nash, and Rolls-Royce. It also found use during World War II in some military vehicles. From 1950 to 1954, Lincoln cars were also available with the Hydra-Matic. Mercedes-Benz subsequently devised a four-speed fluid coupling transmission that was similar in principle to the Hydra-Matic, but of a different design.

Interestingly, the original Hydra-Matic incorporated two features which are widely emulated in today's transmissions. The Hydra-Matic's ratio spread through the four gears produced excellent "step-off" and acceleration in first, good spacing of intermediate gears, and the effect of an overdrive in fourth, by virtue of the low numerical rear axle ratio used in the vehicles of the time. In addition, in third and fourth gear, the fluid coupling only handled a portion of the engine's torque, resulting in a high degree of efficiency. In this respect, the transmission's behavior was similar to modern units incorporating a lock-up torque converter.

In 1956, GM introduced the "Jetaway" Hydra-Matic, which was different in design than the older model. Addressing the issue of shift quality, which was an ongoing problem with the original Hydra-Matic, the new transmission utilized two fluid couplings, the primary one that linked the transmission to the engine, and a secondary one that replaced the clutch assembly that controlled the forward gearset in the original. The result was much smoother shifting, especially from first to second gear, but with a loss in efficiency and an increase in complexity. Another innovation for this new style Hydra-Matic was the appearance of a Park position on the selector. The original Hydra-Matic, which continued in production until the mid-1960s, still used the reverse position for parking pawl engagement.

The first torque converter automatic, Buick's Dynaflow, was introduced for the 1948 model year. It was followed by Packard's Ultramatic in mid-1949 and Chevrolet's Powerglide for the 1950 model year. Each of these transmissions had only two forward speeds, relying on the converter for additional torque multiplication. In the early 1950s, BorgWarner developed a series of three-speed torque converter automatics for American Motors, Ford Motor Company, Studebaker, and several other manufacturers in the US and other countries. Chrysler was late in developing its own true automatic, introducing the two-speed torque converter PowerFlite in 1953, and the three-speed TorqueFlite in 1956. The latter was the first to utilize the Simpson compound planetary gearset.

General Motors produced multiple-turbine torque converters from 1954 to 1961. These included the Twin-Turbine Dynaflow and the triple-turbine Turboglide transmissions. The shifting took place in the torque converter, rather than through pressure valves and changes in planetary gear connections. Each turbine was connected to the drive shaft through a different gear train. These phased from one ratio to another according to demand, rather than shifting. The Turboglide actually had two speed ratios in reverse, with one of the turbines rotating backwards.

By the late 1960s, most of the fluid-coupling four-speed and two-speed transmissions had disappeared in favor of three-speed units with torque converters. Also around this time, whale oil was removed from automatic transmission fluid. By the early 1980s, these were being supplemented and eventually replaced by overdrive-equipped transmissions providing four or more forward speeds. Many transmissions also adopted the lock-up torque converter (a mechanical clutch locking the torque converter pump and turbine together to eliminate slip at cruising speed) to improve fuel economy.

As computerized engine control units (ECUs) became more capable, much of the logic built into the transmission's valve body was offloaded to the ECU. Some manufacturers use a separate computer dedicated to the transmission called a transmission control unit (TCU), also known as the transmission control module (TCM), which shares information with the engine management computer. In this case, solenoids turned on and off by the computer control shift patterns and gear ratios, rather than the spring-loaded valves in the valve body. This allows for more precise control of shift points, shift quality, lower shift times, and (on some newer cars) semi-automatic control, where the driver tells the computer when to shift. The result is an impressive combination of efficiency and smoothness. Some computers even identify the driver's style and adapt to best suit it.

ZF Friedrichshafen and BMW were responsible for introducing the first six-speed (the ZF 6HP26 in the 2002 BMW E65 7-Series). Mercedes-Benz's 7G-Tronic was the first seven-speed in 2003, with Toyota introducing an eight-speed in 2007 on the Lexus LS 460. Derived from the 7G-Tronic, Mercedes-Benz unveiled a semi-automatic transmission with the torque converter replaced with a wet multi clutch called the AMG SPEEDSHIFT MCT. The 2014 Jeep Cherokee has the world's first nine-speed automatic transmission for a passenger vehicle to market.

Hydraulic automatic transmissions

The predominant form of automatic transmission is hydraulic machinery|hydraulically operated; using a fluid coupling or torque converter, and a set of epicyclic gearing|planetary gearsets to provide a range of gear ratios.


Hydraulic automatic transmissions consist of three major components:

Torque converter

A type of fluid coupling, hydraulically connecting the engine to the transmission. This takes the place of a friction clutch in a manual transmission. It transmits and decouples the engine power to the planetary gears, allowing the vehicle to come to stop with the engine still running without Stall (engine)|stalling.

A torque converter differs from a fluid coupling, in that it provides a variable amount of torque multiplication at low engine speeds, increasing breakaway acceleration. A fluid coupling works well when both the impeller and turbine are rotating at similar speeds, but it is very inefficient at initial acceleration, where rotational speeds are very different. This torque multiplication is accomplished with a third member in the coupling assembly known as the stator, which acts to modify the fluid flow depending on the relative rotational speeds of the impeller and turbine. The stator itself does not rotate, but its vanes are so shaped that when the impeller (which is driven by the engine) is rotating at a high speed and the turbine (which receives the transmitted power) is spinning at a low speed, the fluid flow hits the vanes of the turbine in a way that multiplies the torque being applied. This causes the turbine to begin spinning faster as the vehicle accelerates (ideally), and as the relative rotational speeds equalize, the torque multiplication diminishes. Once the impeller and turbine are rotating within 10% of each other's speed, the stator ceases to function and the torque converter acts as a simple fluid coupling.

Planetary gears train

Consisting of planetary gear sets as well as clutches and bands. These are the mechanical systems that provide the various gear ratios, altering the speed of rotation of the output shaft depending on which planetary gears are locked.

To effect gear changes, one of two types of clutches or bands are used to hold a particular member of the planetary gearset motionless, while allowing another member to rotate, thereby transmitting torque and producing gear reductions or overdrive ratios. These clutches are actuated by the valve body (see below), their sequence controlled by the transmission's internal programming. Principally, a type of device known as a sprag or roller clutch is used for routine upshifts/downshifts. Operating much as a ratchet, it transmits torque only in one direction, free-wheeling or "overrunning" in the other. The advantage of this type of clutch is that it eliminates the sensitivity of timing a simultaneous clutch release/apply on two planetaries, simply "taking up" the drivetrain load when actuated, and releasing automatically when the next gear's sprag clutch assumes the torque transfer. The bands come into play for manually selected gears, such as low range or reverse, and operate on the planetary drum's circumference. Bands are not applied when drive/overdrive range is selected, the torque being transmitted by the sprag clutches instead. Bands are used for braking; the GM Turbo-Hydramatics incorporated this.

Hydraulic controls

Uses special transmission fluid sent under pressure by an oil pump to control various clutches and bands modifying the speed of the output depending on the vehicle's running condition.

Not to be confused with the impeller inside the torque converter, the pump is typically a gear pump mounted between the torque converter and the planetary gearset. It draws transmission fluid from a sump and pressurizes it, which is needed for transmission components to operate. The input for the pump is connected to the torque converter housing, which in turn is bolted to the engine's flexplate, so the pump provides pressure whenever the engine is running and there is enough transmission fluid, but the disadvantage is that when the engine is not running, no oil pressure is available to operate the main components of the transmission, and is thus impossible to push-start a vehicle equipped with an automatic transmission. Early automatic transmissions also had a rear pump for towing purposes, ensuring the lubrication of the rear-end components.

The governor is connected to the output shaft and regulates the hydraulic pressure depending on the vehicle speed. The engine load is monitored either by a throttle cable or a vacuum modulator. The valve body is the hydraulic control center that receives pressurized fluid from the main pump operated by the fluid coupling/torque converter. The pressure coming from this pump is regulated and used to run a network of spring-loaded valves, check balls and servo pistons. The valves use the pump pressure and the pressure from a centrifugal governor on the output side (as well as hydraulic signals from the range selector valves and the throttle valve or modulator) to control which ratio is selected on the gearset; as the vehicle and engine change speed, the difference between the pressures changes, causing different sets of valves to open and close. The hydraulic pressure controlled by these valves drives the various clutch and brake band actuators, thereby controlling the operation of the planetary gearset to select the optimum gear ratio for the current operating conditions. However, in many modern automatic transmissions, the valves are controlled by electro-mechanical servos which are controlled by the electronic engine control unit (ECU) or a separate transmission control unit.

The hydraulic & lubricating oil, called automatic transmission fluid (ATF), provides lubrication, corrosion prevention, and a hydraulic medium to convey mechanical power (for the operation of the transmission). Primarily made from refined petroleum, and processed to provide properties that promote smooth power transmission and increase service life, the ATF is one of the few parts of the automatic transmission that needs routine service as the vehicle ages.

The multitude of parts, along with the complex design of the valve body, originally made hydraulic automatic transmissions much more complicated (and expensive) to build and repair than manual transmissions. In most cars (except US family, luxury, sport-utility vehicle, and minivan models) they have usually been extra-cost options for this reason. Mass manufacturing and decades of improvement have reduced this cost gap.

In some modern cars, computers use sensors on the engine to detect throttle position, vehicle speed, engine speed, engine load, etc. to control the exact shift point. The computer transmits the information via solenoids that redirect the fluid the appropriate clutch or servo to control shifting.


Random Page | Longest Wikis | Oldest Wikis | Newest Images | Newest Wikis | List of Categories | List of Every Freakin Wiki



Register to Edit
It takes less than 5 minutes to request registration for editing, and we try to approve within 24 hours. Click the Register Link in the Top Bar.
MoparWiki Help
While editing Wikis may at first glance appear a little overwhelming, it really isn't. You will find this site's HELP (link found in the sidebar) to be very strong and easy to understand. The best way to start is with small edits and working on your user page -- and you will become a Pro in no time.

References